Quick diagnosis
What this code is telling you
Most likely trigger
Damaged or broken lid latch strike
Recommended replacement
Lid Lock Switch Assembly
Diagnostic path
4 ordered checks
Part fit
Exact model number required
Safety first
Before opening the appliance
Unplug the appliance before removing panels or testing internal components. Do not bypass safety switches or live-test high-voltage, gas, refrigerant, or combustion components unless you are qualified to do so.
Read the full safety disclaimerRoot cause
Why the control reported this error
The washer sets this code when its control cannot confirm the expected wash-cycle condition. Start by ruling out damaged or broken lid latch strike. faulty door lock switch assembly and loose wiring harness connector can create the same feedback, so confirm the failure before replacing lid Lock Switch Assembly.
Symptoms
What you may notice
- ✓Washer will not start cycle
- ✓Lid lock light flashes red or blinks
- ✓Door fails to lock during spin cycle
Possible causes
Check the most likely causes first
- 1
Damaged or broken lid latch strike
Start here when it matches your symptoms.
- 2
Faulty door lock switch assembly
- 3
Loose wiring harness connector
- 4
Failed main electronic control board
Diagnostic sequence
Work through these checks in order
Stop when you find the fault. Do not perform a step that requires skills or live testing you are not qualified to do.
- 1
Check 1
Disconnect power to the washer for 5 minutes to reset the control board.
- 2
Check 2
Check lid latch mechanism for physical obstruction, debris, or broken plastic tabs.
- 3
Check 3
Disconnect electrical power before opening panels. Inspect wiring harness running between the lock switch and control unit for loose pins.
- 4
Check 4
Disconnect electrical power before opening panels. Test lid lock switch for electrical continuity using a multimeter; replace lock assembly if open circuit.
Replacement part reference
Lid Lock Switch Assembly
Exact OEM part number
Model number required
Fitment note
The exact OEM part number varies by model and production revision. Verify the complete model number before ordering.
Verify the appliance model before ordering.
Manufacturers can use different parts under the same error code across model families and production revisions.
Where do I find my model number? →FixCodeDB may earn a commission from qualifying purchases made through affiliate links.
Common questions
Quick answers for this fault
What should I check first for F5E2?
Start with damaged or broken lid latch strike. If that checks out, continue through the diagnostic sequence above rather than replacing a part based on the code alone.
Does F5E2 always mean Lid Lock Switch Assembly is bad?
No. An error code identifies the condition the control detected, not a guaranteed failed part. Confirm the likely causes and wiring first. The exact OEM part number varies by model and production revision. Verify the complete model number before ordering.
When should I stop troubleshooting F5E2 myself?
Stop if the next step requires live electrical testing, sealed-system work, gas or combustion service, or any procedure outside your training. Unplug the appliance before removing panels or testing internal components. Do not bypass safety switches or live-test high-voltage, gas, refrigerant, or combustion components unless you are qualified to do so.
Manufacturer reference
Verify against the official support source
FixCodeDB summarizes the fault in plain language. For model-specific instructions, confirm the guidance with the manufacturer and your appliance manual.
Whirlpool Front Load Washer Error Codes — Whirlpool Product Help →Was this useful?
Did these checks help with your Whirlpool F5E2 error?
Keep diagnosing
Related Whirlpool guides
dET appears on select models when the detergent cartridge is not detected in the dispenser.
F0E5 code indicates an off-balance wash load prevented the unit from reaching full spin speed.
Whirlpool washer code F1E1 signals a critical primary hardware failure on the main electronic control unit (CCU).
F7E1 indicates that the motor cannot achieve the expected speed for the selected cycle.
Different problem?
Search another code or symptom
Go back to the main diagnostic search and try the code, symptom, appliance, component, or brand.
Open diagnostic search →